16 mn cr 5 chemical

1.7147 Material 20MnCr5 Steel Equivalent, Properties

Treated to ferrite-pearlite structure and hardness:152-201 HBW. Normalized:140-201 HBW. 20MnCr5, 1.7147 Tensile strength (after hardening and tempering at 200 °C) Dia. 16mm:Min. 1200 MPa. 16 < Dia. 40mm:Min. 900 Mpa. 40 < Dia. 100mm:Min. 700 Mpa. 16MnCr5 - OvakoGeneral Information 16MnCr5 is an alloyed case hardening steel used for e.g. mechanical engineering components.The steel can be M-treated in order to optimize the machinability. For additional Heat Treatment Data, please visit the Heat Treatment Guide.

16MnCr5,16MnCr5 Chemical composition,16MnCr5 steel

16MnCr5,16MnCr5 Chemical composition,16MnCr5 steel grades. BEBON STEEL offer 16MnCr5,16MnCr5 Chemical composition,16MnCr5 steel grades,if you need EN 10084 :2008 Case hardening steels. Technical delivery conditions ,please contact us. Grade :16MnCr5. Number: 16MnCrPb5 / 16 MnCrPb 5 Datasheet, chemical composition 21 rows · This page cover the 16 MnCrPb 5/16MnCrPb5 Chemical element, Mechanical Properties, 16MnCrS5 (W. NR. 1.7139) Special alloy case-hardening CHEMICAL COMPOSITION:(heat analysis according to the EN 10277-4 standard) C % Si % Mn % P % S % Cr % FROM 0,14 - 1,00 - 0,020 0,80 Hardness maximum values HB Hardness maximum values HB 510 - 260 >1016 - 250 >1640 207 245 >4063 207 240 >63100 207 240 * Delivery condition:subjected to a softening treatment according to the

20MnCr5 - Ovako

Variant Cast Weldability C % Si % Mn % P % S % Cr % Ni % Mo % Cu % Al % 236Q:IC:CEV 0.73 max:Min:0.17:0.10:1.10--1.00:0.10--0.050:Pcm 0.38 max:Max:0.22:0 Chemical Composition - Steelmetal3. For product thicknesses<6 mm, a minimum Mn of 0.6 percent is permitted. 4. The minimum Al (total) content may not be applicable, if Nb, Ti or V either singly or in combination are additionally used for Nitrogen binding. 5. If only Al is used for nitrogen binding, a ratio Al/N>=2 shall apply. 6. Cr+Cu+Mo shall not exceed 0.45 percent. 7. EN 1.7139 (16MnCrS5) Chromium Steel ::MakeItFromEN 1.7139 (16MnCrS5) Chromium Steel. EN 1.7139 steel is an alloy steel formulated for primary forming into wrought products. 1.7139 is the EN numeric designation for this material. 16MnCrS5 is the EN chemical designation. It has a moderately low embodied energy and a moderately low base cost among EN wrought alloy steels.

GRADE % C % Mn % P % S % Si % Cr % Ni % Mo % Al %

GRADE % C % Mn % P % S % Si % Cr % Ni % Mo % Al % Cu % V % Ti 0.35 0.50 0.020 0.10 0.90 - 0.20 0.020 - - - 0.45 0.80 0.035 0.035 0.35 1.20 - 0.35 0.040 - - - 42CrMo4 / 0.38 0.50 - 0.020 0.15 0.90 - 0.15 0.020 - - - 42CrMoS4 0.45 0.80 0.035 0.035 0.40 1.20 - 0.30 0.040 - - - Material Data Sheet 1.7131, 16 Mn Cr 5 - EC 80, 5115Quick Metall sources you with the Material 1.7131, 16 Mn Cr 5 - EC 80, 5115:Edelbaustahl / Einsatzstahl, Maschinenbau - Zahnräder - GelenkeEN 1.7131 Steel 16MnCr5 Material Equivalent, Composition 3 rows · EN 1.7131 steel (16MnCr5 material) is an European standard carburized steel (case hardening steel)