high yield prime alloy steel bar

317L - Rolled Alloys, Inc.

Alloy 718 (AMS 5663) is bar that is already aged (precipitation hardened). As supplied, this material provides high tensile strength and hardness compared to 718 in the annealed condition. Alloy X AISI 4340 Alloy Steel Bar - wihometals4340 is a low alloy, nickel-chromium-molybdenum Machinery steel capable of being heat-treated to high strength levels. The alloy has a good combination of ductility, toughness and strength along with high hardenability. It has been used for where high strength and heavy-duty are required in heavy sections such as turbine shafts with a diameter greater than 250mm, rotor shafts of helicopters, turboshafts and blades of turbojet engines, high

Alloy Chatham Steel

Alloy:High Strength:Quenched and tempered alloy steel plates used primarily for their high yield-t0-weight ratio. 100,000 min. yield:ASTM A-514 Construction Grade:3/16" to 6" 4'x8' through 10'x40' Abrasion Resistant:As-Rolled AR steel, not quenched and tempered, for moderate wear applications:AR 225/235:3/16" to 1" 4'x8' through 8'x20' Alloy Steel 4140 - AmeralloySupplied in the annealed or prehardened condition. 4140 PREHARD is heat treated to a medium hardness (HRC 28/32) and is designated as 4140 HT. 4140 annealed is supplied in the soft condition and can be hardened to RC 40. 4140 HT is supplied in many forms such as hot rolled or turned, ground and polished rounds and DCF plate to be used as a holder material for high strength structural components. 4140 Prehard is stocked in a DCF, ground finished 4140 HT is available in plate, flat bar EN353 Alloy Steel EN353 Forging EN353 Flat - Saaj SteelEN353 steel round bars offer a good combination of ductility, strength, and wear resistance. EN353 is a very high-strength alloy engineering steel. Stress Relieving:150-200, cooled in the furnace. 1st pre-heating °C:Up to approx. 400 in an air-circulating furnace 2nd and 3 rd:780 and 805°C. Normalizing:860 890°C in air. Annealing:630-670°C

HIGH STRENGTH - Standards - ASTM Standards

This standard covers high strength low-alloy structural steel shapes, plates and bars for use in riveted, bolted or welded construction with minimum yield point strengths of 50,000 psi (345 MPa). The atmospheric corrosion resistance of this steel is substantially better than that of carbon structural steel. This steel is available in four different chemical compositions, designated Grade A, B, C and K. High Tensile & High Yiled Strength Steel - Tremor AlloysAs an unalloyed low carbon mild steel grade S355 is supplied in the hot rolled condition. The S355 steel specifications are high yield non alloy steels. First specified in the European EN10025 standard and later published by the British Standards Institure (BSI) as BS EN 10025 S355, S355J2 and S355J2 N. These standards superceded the BS4360 grades. High-Strength Reinforcing Bars Technical NoteGrade 60 reinforcing steel, with a yield strength of 60,000 psi, is the most com-monly used Grade in North America. Recent advances have enabled reinforcing steels of higher strengths to be commer-cially produced. In ATC 115 (ATC 2014), high-strength re-inforcing bars (HSRB) were considered any reinforcing bar with a yield strength greater than 60,000 psi.

Kromite® #3 HT 4140 Steel Associated Steel Corporation

High Strength Steels Kromite® #3 HRHT (4140/4150 Mod) High Strength, Prehard Alloy. Kromite #3 is a modified 4140/4150 steel. This chromium and molybdenum based alloy is electric furnace melt, vacuum degassed, stress relieved, and machine straightened. It is offered in the hot roll, heat treated condition. Plate Products Infra-Metals Co.ASTM A588 . Standard specification for high-strength low-alloy structural steel. This specification covers shapes for welded, riveted, or bolted construction but intended primarily for use in welded bridges and buildings where savings in weight or added durability is important. S700MC High Yield Steel__Steel SupplierS700MC a high yield structural steel supplied under the EN10149:Part2 specification. Due to the materials high yield (700Mpa min.) it can be used in a variety of load bearing applications. Popularly, the steel is used for cold formed components including cold pressed parts and sections.

high yield steel, high yield steel Suppliers and

A wide variety of high yield steel options are available to you, such as aisi, astm, and jis. You can also choose from bending, cutting, and welding high yield steel, as well as from container plate, boiler plate, and flange plate high yield steel, and whether high yield steel is ce, lfgb, or cb.prime alloy deformed steel bar, prime alloy deformed steel High yield iron rods steel rebar kuwait deformed steel bar PRIME REINFORCING DEFORMED STEEL BARS (Hot Rolled) Origin:Turkey Quality:ASTM A615 Gr40-60, BS4449:97 Grade 460B, DIN488 BST 500S, CA-50 Size:8-32mm Length:6-12m Packaging:2 MT bundles. is an integrated and professional building & decoration materials provider in Guangzhou of China.