s250gd z100 az70 means

AZ coating steel coil/GL/AZ40 GL/AZ50 GL - Suzhou GWB

GL Alu-zinc coated steel coil, Alu-zinc steel coil, AZ coating steel coil, AZ steel coil, AZ100 GL, AZ120 GL, AZ150 GL, AZ200 GL, AZ30 GL, AZ40 GL, AZ50 GL, AZ60 GL, AZ70 GL, AZ80 GL, AZ90 GL, galvalume steel coil, GL, HDGL, hot dip aluminum zinc steel coil Appendix 1 to Declaration of Performance NO. 02/3/14509BALEX METAL Sp. z o.o., CENTRALA 84-239 Bolszewo, ul. Wejherowska 12C, tel. +48 58 778 44 44, fax:+48 58 778 44 55 e-mail:[email protected], balex.eu, NIP PL

Appendix 1 to Declaration of Performance NO. 03/1/14509

BALEX METAL Sp. z o.o., CENTRALA 84-239 Bolszewo, ul. Wejherowska 12C, tel. +48 58 778 44 44, fax:+48 58 778 44 55 e-mail:[email protected], balex.eu, NIP PL EN 10169 Coated steel sheets, flat productsS250GD (material number 1.0242) S280GD (material number 1.0244) S320GD (material number 1.0250) S350GD (material number 1.0529) with chemical composition and mechanical properties in accordance with the requirements of EN10346. The available coating masses:Sheet metal with zinc coating. Coating mass:Z100, Z140, Z200, Z225, Z275. GalvInfoNote Understanding Coating Weight dip, the use of the letter G means it is a SI coating. Conversely, use of the letter G in the coating designator of ASTM hot-dip products means it is an Inch-Pound coating. For example, the designator 40G40G (sometimes referred to loosely asG40/40 ) in A 879/A 879M (g/m2), is easy to confuse withA 653 /A 653M G40 (oz /ft2),

Galvanised Material

Gr255 S250GD - - 0.5 - 3.0 - 280 360 18 4998:Gr280 Gr275 S280GD - - 0.7 - 3.013 - 350 420 16 4998:Gr350 Gr340 S350GD - - 0.3 - 1.2 - 550 560 - 4998:Gr550 Gr5506 S550GD12 Z100 1 Z150 2 Z200 Z275 Z4503 Z6003 60 80 100 150 200 275 450 600 40 60 85 128 170 235 385 510 4 6 7 10 14 19 32 42 GreenCoat PLX Legacy highly formable tinsmith product - This means that the product is recommended for long-strip roofing providing very tight folding. S250GD-S350GD, DX51D :Z100:0.50 mm:1000-1500 mm:Laminate Foodsafe:S250GD-S350GD, DX51D :Z275:0.42 mm:1000-1400 mm:Epoxy:S250GD-S350GD, DX51D :Z100:0.40 mm:1000-1500 mm * In addition to these we have a wide range of so called custom Hot-dip galvanised steel acc. DIN EN 10346-DX51D,DX53D Hot-dip galvanised steel in the grade DX51D, DX52D, DX53, DX54D, DX56, DX57D and S220GD, S250GD, S320GD, S350GD, S390GD, S420GD, S450GD, S550GD.

Public Record 181

EN10346 S220GD, S250GD, S280GD, S320GD, S350GD, S550GD JIS 3321 SGLC400, SGLC440, SGLC490, SGLC570 General and Commercial Grades Forming, Pressing & Drawing Grades Structural Grades Figure 2:International Standards for aluminium zinc steel6 Tariff classification (i) Galvanised steel TDS-06-54 Tempofor F3 17-03-2014 - RamuddenThe designation of the steel is:S250GD Z100. 3 Properties 3.1 Welded mesh infill 3.1.1 Wire diameter and tolerances See table 3 :Table 3:Wire dimensions and tolerances Wire diameter and tolerances (mm) Vertical Horizontal 3,00 ± 0,10 3,40 ± 0,10 3.1.2 Mesh spacing Tempofor F2 Eco - CloudinaryThe designation of the steel is:S250GD Z100. 3 Properties 3.1 Welded mesh infill 3.1.1 Wire diameter and tolerances See table 3 :Table 3:Wire dimensions and tolerances Wire diameter and tolerances (mm) Vertical Horizontal 3,40 ± 0,10 3,80 ± 0,10 3.1.2 Mesh spacing Mesh spacing is measured from centre to centre, wire or tube.

Zinc coating (Z) - Hot-dip galvanized steel - SSAB

Zinc coating (galvanized coating) produced by hot-dip galvanizing offers a formable zinc coating with galvanic corrosion protection from Z100 to Z600. Zinc coating (Z) produced on both sides by hot-dip galvanizing extends the service life of the end product by protecting the steel from corrosion.Metal coated EN10346:2015; S220GD, S250GD, S280GD, Metal coated structural steels according to EN10346:2015 are made for thin-gauge structural applications that call for load-bearing capacity and good galvanic corrosion protection. S220GD, S250GD, S280GD, S320GD, S350GD